Am concerned as am now doing a fairly new pine wood (with semi-gloss to satin dark finish) coffee table set which will have heavier use and want to ensure no chipping. Intended to do same process using shellac primer for bottoms and natural wood stained on the tops, Can you provide any guidance as to my process/outcome? Am trying to be very thorough to ensure good end result. There are some paints or primers that say right on the label “Do not use TSP” – B.I.N Shellac Primer being one example. So always reading the paint/primer label before you start is a great habit to get into. I’ve never heard/read TSP couldn’t be used before painting with Chalky Paints, and I’ve done it many times with no adverse effects.

Those bubbles will dry in the finish and need to be sanded out. Three coats of poly are usually needed to give projects the proper amount of protection. The first coat or base coat of polyurethane should be thinned. A base coat is two parts of polyurethane to one part of paint thinner. The second and third coats are applied at full strength.

Uses For Wall Paint

Just ruined an entire set of shelves I built because I followed this advice. The water based poly raised the grain of the wood and now to get it smooth again I’d have to sand down the wood which is taking off the oil based stain that I did weeks ago. If you do end up applying a topcoat for added UV protection, I suggest that you investigate a water based exterior product. Polyurethane will yellow over time and get darker.

• And if you re-stain with the same exterior color it will be darker.
• My second favorite color was Minwax Coastal Gray.
• Usually, water based jobs can be done in 2 days and you can walk on it that night; oil based can take 3-5 days and you need to wait at least 24 hrs before walking on them.

You will need to apply the substance in a well-ventilated area while wearing the appropriate protection, particularly a mask that covers the nose and mouth. Plus, if you are covering a surface on an item that may be moved from indoors to outdoors from time to time, then they can provide answers for that as well. You will need to keep this in mind when deciding which product to purchase. As noted earlier, the main advantage of spar urethane is its resistance to the elements such as water, light, and heat.

Pros To Wall Paint

They have done this by introducing myths into their instructions. Some of the myths make no sense but do no harm. Others purport to solve a problem, and when following them doesn’t help, frustration sets in. The first clue that sanding between coats isn’t so critical is that you rarely create scratches everywhere anyway.

It comes in a rectangular can and goes on fast and easy and has a very silky finish. I always have drips when I paint any topcoat on. The only problem I’ve had with polycrylic in the past is using it over a light blue paint. It changed completely changed the color of my paint.

Chemistry Of Polycrylic Vs Polyurethane

Hmmm, not sure it’s ever been done before but I would recommend priming/sealing with a drywall primer before applying any type of paint. I have painted outdoor furniture with chalk paint and an outdoor poly makes it super durable. I just painted my old 1/2 bath cabinet with regular acrylic paint & wonder what to seal them with. I don’t want to see brush strokes (like when I’ve brushed liquid polyurethane on before. Wax? liquid? brand?Suggestions appreciated. Regular ShWillimas cheap paint Thank you. I then tried water based polycrylic but I made the colour turn to a dirty beige/dark cream colour which I didn’t like.

However, it dries quicker, has less odor, and cleans up easier than fully oil-based polyurethane. There’s no doubt that Bona Mega Wood Floor Finish is our top waterborne polyurethane product. It’s an oxygen crosslinked polyurethane that is proven to improve the look, feel, and durability of wood flooring. Bona’s installation process couldn’t be more user-friendly. You can apply the product using a variety of application techniques.

The layers of film refract light and gives a shiny or glossy appearance. Polyurethanes come in varying sheen levels including matte, however due to build up, matte polyurethanes appear different than hardwax oils. As you begin to wet-sand, use your free hand to feel the wood that you have just sanded. You will probably love the feel of the wood, even if you are using regular polyurethane. If you are not quite satisfied, then sand to the next higher grit.

If the stain is cured and inactive, the mineral spirits will not affect the color. You should not have any color pick-up minwax vs varathane onto the cloth. The mineral spirits will remove any active/excess stain from surface and help the stain to cure out.

You must wait approximately 2 hours before adding a new coat. The finish should be ready for light use minwax vs varathane after about 24 hours. A single quart of this product should cover roughly 125 square feet of flooring.

I tried brushing the Polycrylic, and it was streaky. The process includes a few simple steps along with choosing the right epoxy minwax vs varathane products and knowing what they are for and how to use them. Epoxy can be applied to structural fabric as well as non-structural.

Plan to use a bit more elbow grease to take off the paint, or distress it right after it has finished drying. You can add a bonding agent to the paint that ensures it will adhere to furniture that has already been finished. Milk paint is an all-natural paint made with, you guessed it, milk protein! It’s been used for centuries and creates a natural, old-world look.

Synthetic bristle brushes, foam brushes, and lambswool applicators are all suitable options for interior wood surfaces. All three finishes give hardwood floors a rich, timeless look. However, semi-gloss handles frequent cleaning best. You need to apply several layers to cash in on the durability of this product. Fortunately, it only takes 2 to 3 hours for each application to dry.

Also, a tack cloth works well to remove fine dust right before you go to apply your product. It should go without saying that dust management is paramount in the finishing process. Sometimes it may be necessary to hang plastic, visqueen, or some sort of barrier to keep the dust out.

In this article, we will take you through both of these products and explain which situation is best for which one. That will help you when choosing a product for your finishing. That sell it in a store near me and they said it’s easier than chalk paint. I want to paint a couple of old wooden dressers. I’ve always been an artsy person, so getting into furniture repainting just seemed right. That being said, I had no idea what paint to go with.

Condition the wood.After sanding wood, using something like Varathane’s Wood Conditioner or Minwax’s Sanding Sealer to prepare the wood. If you jump right into staining without preparing the wood, the stain simply will not take or dry the way that you want. Your finish should overtake the look of the wood itself, but instead enhance it. If you have a naturally dark wood that you need to stain, consider more of a glossy stain. However, if you have a noticeably light wood that you want to darken, look for more walnut, espresso, and mocha tinted stains. If you prefer water based, their Ultimate Polyurethane Water Based is just as effective as oil, with the main difference being the 4-coat application.

Source: https://homemakerguide.com/